Can I Install a Bath Tub Myself? Factors to Consider As Well As Steps
Can I Install a Bath Tub Myself? Factors to Consider As Well As Steps
Blog Article
Are you interested in know-how about How to Install a Bathtub Yourself?
Mounting a bathtub isn't exactly rocket science, yet it does require solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably difficult project. If the old tub is conveniently accessible, the project can relocate easily; if you have to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to vacate the old tub as well as set in the new one. Make sure you have certified on your own for the job as well as fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is much better to think about using one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This post will certainly assist you install a new bathtub in your restroom if you have already purchased a new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and product list should consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Secure the faucet in position with the maker provided backnut. When the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile faucet port to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and check all joints as well as new pipework for leaks and also tighten them if required. Fill up the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the tub must wait till the tub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.
Preparing for the Installation
Firstly, the supporting structure supplied with the bath needs to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to stop stress on the tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill the tub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about Installing A Bathtub, I was thinking sharing that piece of writing was a smart idea. Kindly take a moment to share this page if you appreciated it. We cherish reading our article about How to Install a Bathtub Yourself.
Estimating
Report this page